We have uncovered this article pertaining to A Step-by-Step Guide to Installing a Bathtub below on the net and reckoned it made sense to write about it with you on this page.
Installing a tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the project can relocate speedily; if you have to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have actually certified on your own for the work and also are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you start. Possibilities are you might require a specialist plumber to make tube links.
This write-up will assist you set up a brand-new tub in your shower room if you have actually currently gotten a new tub and don't need to transform the setup of your previous water pipelines.
Your devices and also product list ought to make up the following:
- New Bath tub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Knife
- Measuring tape
- Pipe Caps
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in place between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type must be connected to the tap finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system and also check all joints and new pipework for leakages and also tighten them if essential. Fill the bath tub as well as also check the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait until the bathtub has actually been made use of at the very least once as this will certainly settle it into its final position.
Preparing for the Installment
To start with, the sustaining framework provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing problems with dampness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water before securing, to enable the motion experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Installing A Bathtub? Create feedback directly below. We would be glad to find out your suggestions about this blog. Hoping that you visit us again later on. So long as you enjoyed reading our blog posting plz be sure to share it. Thanks for taking the time to read it.
Show Details
Comments on “A Step-by-Step Guide to Installing a Bath Tub”